{"product_id":"victron-smart-batteryprotect-12-24v-220a-tiefenentladeschutz","title":"Victron Smart BatteryProtect 12\/24V-220A Deep Discharge Protection","description":"\u003ch2\u003eSmartBatteryProtect 12\/24V 220 A by Victron Battery Protection with Bluetooth\u003c\/h2\u003e \u003cp\u003eThe BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage it) or before it no longer has enough power to start the engine.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eBluetooth: Easy Programming\u003c\/strong\u003e\u003cbr\u003eBy using Bluetooth to program the Smart BatteryProtect, all necessary\u003cbr\u003eon\/off thresholds can be set.\u003cbr\u003eAlternatively, one of nine pre-set on\/off thresholds can be set using the programming pin\u003cbr\u003e(see manual).\u003cbr\u003eIf necessary, the Bluetooth function can be deactivated.\u003c\/p\u003e\u003cb\u003e12\/24 V automatic voltage range detection\u003c\/b\u003e \u003cp\u003eThe BatteryProtect automatically detects the system voltage.\u003c\/p\u003e\u003cb\u003eEasy Programming\u003c\/b\u003e \u003cp\u003eThe BatteryProtect can be set to switch on and off at several different voltages. The seven-segment display then indicates which setting has been selected.\u003c\/p\u003e\u003cb\u003eA special setting for lithium-ion batteries\u003c\/b\u003e \u003cp\u003eIn this mode, the BatteryProtect can be controlled by the VE.Bus BMS. Note: The BatteryProtect can also be used as a charge breaker between a battery charger and a Li-ion battery. See wiring diagram in the manual.\u003c\/p\u003e\u003cb\u003eExtremely low power consumption\u003c\/b\u003e \u003cp\u003eThis is important in the case of lithium-ion batteries, especially after shutdown due to a low voltage level. Please also refer to our data sheet on lithium-ion batteries and the VE.Bus BMS manual for further information.\u003c\/p\u003e\u003cb\u003eOvervoltage protection\u003c\/b\u003e \u003cp\u003eTo prevent sensitive loads from being damaged by overvoltage, the load is always switched off when the DC voltage exceeds 16 V or 32 V.\u003c\/p\u003e\u003cb\u003eExplosion protection\u003c\/b\u003e \u003cp\u003eNo relays but MOSFET switches and therefore no spark formation. Output for delayed alarm The alarm output is activated when the battery voltage drops below the preset switch-off value for more than 12 seconds. Starting the engine therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. current 50 mA. The alarm output is normally used to activate an acoustic signal, an LED or a relay.\u003c\/p\u003e\u003cb\u003eLoad disconnect and reconnect delay\u003c\/b\u003e \u003cp\u003eThe load is switched off 90 seconds after the alarm is activated. If the battery voltage rises again within this period (after the engine has been started, for example) to the reconnect threshold, the load is not switched off. The load is reconnected 30 seconds after the battery voltage has exceeded the specified voltage value for reconnection.\u003cbr\u003e\u003c\/p\u003e\u003ch4\u003eDocuments \u0026amp; Downloads\u003c\/h4\u003e\u003cul\u003e\n\n\u003cli\u003e\u003ca href=\"https:\/\/media.wattstunde.de\/mediafiles\/PDF\/Elektronik\/Victron\/Battery%20Protect\/Smart%20Battery%20Protect\/Datasheet-Smart-Battery-Protect-65-A--100-A--220-A-DE.pdf\" target=\"_blank\"\u003eSmart BatteryProtect Datasheet\u003c\/a\u003e\u003c\/li\u003e\n\n\u003cli\u003e\u003ca href=\"https:\/\/media.wattstunde.de\/mediafiles\/PDF\/Elektronik\/Victron\/Battery%20Protect\/Smart%20Battery%20Protect\/Handbuch_SmartBatterieProtect.pdf\" target=\"_blank\"\u003eSmart BatteryProtect Manual\u003c\/a\u003e\u003c\/li\u003e\n\n\u003cli\u003e\u003ca href=\"https:\/\/media.wattstunde.de\/mediafiles\/PDF\/Elektronik\/Victron\/Battery%20Protect\/Smart%20Battery%20Protect\/8778-VictronConnect_manual-pdf-de.pdf\" target=\"_blank\"\u003eVictron Connect Manual\u003c\/a\u003e\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":57444391682430,"sku":"WS300-3123S","price":152.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0906\/7557\/7214\/files\/victron-smart-batteryprotect-12-24v-220a-tiefenentladeschutz.png?v=1779292130","url":"https:\/\/www.offroad-fittery.de\/en\/products\/victron-smart-batteryprotect-12-24v-220a-tiefenentladeschutz","provider":"Offroad-Fittery","version":"1.0","type":"link"}