Victron Quattro 24/3000/70-50/50 Inverter 2400 W and Charger 24V

Innovative Combination Device from Victron: Sine Wave Inverter and 24V Battery Charger with Transfer Switch in One!

The Victron Quattro 24/3000/70 is a device combination consisting of a 2400 W sine wave inverter, a battery charger, and a transfer switch.
The cleverly integrated battery charger delivers an impressive 120 A, allowing batteries to be charged extremely quickly when shore/grid power is available. The highlight: the device can be connected to two independent AC sources. These can be, for example, a generator and a shore power connection, or two generators. The Quattro automatically switches to the active source.
The sine wave inverter integrated into the Victron Quattro transforms the 24 V DC current from the battery into 230 V AC voltage. Thanks to the true sine wave, the voltage quality is perfectly suited even for sensitive electronic devices.
Furthermore, a lightning-fast 50 A transfer switch is also built in, allowing grid-connected systems to be realized.

Two AC Inputs with Integrated Transfer Switch

The Quattro can be connected to two independent AC sources: for example, to the public grid and a generator, or even to two generators. The Quattro automatically connects to the active source.

Two AC Outputs

The main output ensures uninterrupted operation. In the event of a power outage or an interruption of shore/generator power, the Quattro takes over the supply of the connected consumers. The transfer happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when AC power is available at one of the Quattro's inputs. Consumers that should not discharge the battery, such as a water heater, can be connected to this output.

Virtually Unlimited Power Through Parallel Operation

Up to 6 Quattros can be connected in parallel. For example, six 48/10000/140 units yield 54 kW/60 kVA of power or 840 A of charging current. Three-Phase Operation Three units can be configured for three-phase operation. But that's not all: up to 6 sets of three devices can be connected in parallel, resulting in 162 kW/180 kVA of inverter power and over 2,500 A of charging capacity.

PowerControl – Working with Limited Generator Power, Limited Shore or Grid Power

The Quattro is a very powerful battery charger. Therefore, it draws a lot of current from the generator or shore power supply (16 A per 5 kVA Quattro at 230 VAC). A current limit can be set for each of the AC inputs. The Quattro then considers other connected AC consumers and uses only the "remaining" current for charging. This prevents the generator or grid connection from being overloaded.

PowerAssist – Increasing Shore Connection or Generator Power

With this function, the PowerControl principle gains a new dimension, as the Quattro supports any undersized alternative source. Peak loads often occur only for a limited period. In such a case, the Quattro ensures that an insufficient grid or generator power is immediately compensated by energy from the battery. If the load is reduced, i.e., consumers are switched off, the then sufficiently available energy can be used to charge the batteries.

Solar Power: AC Power Even During a Grid Outage

The Quattro can be used in both off-grid and grid-connected PV systems, as well as in other alternative energy systems. Software for detecting a grid outage is available.

System Configuration -
If settings on a single device need to be changed, this can be done within minutes using a DIP switch setting procedure. - Parallel-connected and three-phase systems can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software. - Off-grid, grid-connected, and self-consumption systems using grid-tie inverters and/or MPPT solar chargers can be configured using assistants (associated software for the respective systems).

On-site Monitoring and Control

Several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (USB or RS232).

Remote Monitoring and Control

Victron Ethernet Remote, Victron Global Remote and the Color Control Panel. The data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. Remote configuration: If systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.

Technical Data

Item number	300-3048
AC continuous power (W)	2400W
Voltage regulation	24V DC / 230V AC
No-load self-consumption	20W
No-load self-consumption in energy-saving mode	10W
Operating ambient temperature range	-40°C to 65°C
Number of battery outputs	2
Battery voltage	24V
IP protection class	IP21
Output voltage (V)	230V AC / alternating current
Current quality	true sine wave
AC output frequency range (Hz)	50Hz / +-0.1Hz
Manufacturer part number	QUA243020010
Product type	Powerful pure sine wave inverter, battery charger with adaptive charging technology, and transfer switch. In addition, the Quattro series can be connected to two independent AC sources.
Transfer switch	1
Manufacturer	Victron Energy
Dimensions	362x258x218
Weight	19 kg
Warranty	5 years manufacturer's warranty
Transfer switch switching capacity (A)	50A

Documents & Downloads

• Datasheet